JIMS Wrist Pin Remover
JIMS Wrist Pin Remover Tool This simple tool can be used easily by one person. No need to get another technician to hold the piston while your drift the pin out. (99-06 Twin Cam) 20287 99-06 Twin Cam (except 06 Dyna) JIMS Piston Ring Compressor Extra fine tooth ratcheting mechanism will compress rings in small increments without breaking. Includes six bands ranging from 2 7/8" to 4 3/8". 400357 Clear Long Timing Plug Tool 894888 Fits Big Twin 70-98 Connecting Rod Clamping Tool Holds rod when fitting piston pin bushing. Used on all V-twin models (repl. OEM 95952-33). Sold each. 400548 Connecting Rod Clamping Tool JIMS Wrist Pin Bushing Tool Removes and replaces the wrist pin bushing without removing the connecting rod from the crankcases. 20295 For Twin Cam 88 models from 99-06 Piston Ring End Gap Tool • Accurate tool to measure ring end gap faster • The flanged design allows the piston ring to fit squarely in cylinder bore every time • Each side of the tool is made for checking a standard size piston rings • For Twin Cam standard size pistons for 95” 103” or 110”, with 3.875” or 4.000” bore 890574 Piston ring end gap tool 19 19.34 Cam Gear Gauge Pins These pins are used to properly determine cam and pinion gear sizes. Sold in pairs. 24196 0.105"-diameter BT 54-89 JIMS Cam & Pinion Gear Gauge Pins Use to check gear diameters when changing cams or pinion gears on single cam Big Twins ONLY. Sold in pairs. 400362 Fits Big Twins from 54-89 (.105" pins) 400363 Fits Evolution Big Twins from 90-99 (.108" pins) JIMS Wrist Pin Bushing Tool Makes it easy to remove and install rod bushings on all models (except Twin Cam 88 models). Complete instructions guide you through removal, selection of new bushing with the proper clearances, and installation. 20169 Fits all Single Cam Big Twins up to 99. Fits 57-20 Sportster, 95-02 Buell and 45” Flathead. JIMS Piston Pin Keeper Tool Makes piston pin retaining ring installation a snap. Fits stock piston pin retainers on Big Twins from 83-99 (except Twin Cam 88 models) and Sportster models from L85-20, 87-10 Buell (exc. 1125). 20674 Sold each Piston Jet Test Stand If you plan to rebuild more than two Twin Cam engines and or lower ends - this tool pays for itself! • Clear the jet of all assembly lubes • Verify the PSI number the jet switches “on” • Visualize the spray pattern • For Twin Cam 99-17 890569 Piston jet test stand
APPAREL SEATS & TOURING Tappet Pump Up Tester • Fill completely your standard size hydraulic tappets • Inspect them physically • With the help of a drill press, check for proper feel 890568 For Twin Cam Magnetic Tappet Holding Tool • The new JIMS® Magnetic Tappet Holder easily holds the tappets in the tappet bores when changing or upgrading cams • Simply install the tool over the tappet cover and the magnets will magnetically hold the tappet in place while performing any cam chest work, a time saver for any technician • Designed to work on both Twin Cam and Milwaukee-Eight engines Part#: 923736 , Fitment: 00-17 Dyna, 00-23 Softail, 00-23 Touring, 09-23 Trike , Unit: Set , Qty.: 1 Vacuum Tappet Pump up Tool Our popular and effective bleed technology that is found in the JIMS brake bleeding tool has now been applied to hydraulic lifters. A special jar, designed for vacuum, holds up to four hydraulic lifters in a convenient tray. Once vacuum is applied, bubbles can be seen escaping from the lifters until they are completely bled. Lifters are now ready to install. No more abuse of the starting system to pump up the lifters, and no risk of damage to the valve train by running the engine, even at low RPM, when lifters have not been fully bled. A detailed manual can be found here: https://www.jimsusa.com/wp-content/ uploads/2019/10/5532-IS.pdf. Part#: 917611 , Fitment: 86-20 Sportster, 85-94 FX Model, 91-17 Dyna, 84-23 Softail, 85-23 Touring, 09- 23 Trike , Unit: Each , Qty.: 1 FOOT CONTROLS HAND CONTROLS LIGHTING ELECTRICAL EXHAUST INTAKE ENGINE Mini-Valve Spring Tester 0 to 1000 P.S.I. Gauge Use this tool in either a bench vice, arbor, hydraulic screw press or a drill press. Tool fits any dual rate or conical valve spring with an O.D. no larger then 1.6” diameter. Precision gauge comes with a protective rubber boot. 890572 Mini-valve spring testerC Tappet Adjustment Tool • This hand tool simplifies the way to verify proper tappet adjustment • Use on most hydraulic tappets, OEM and aftermarket • For Twin Cam, Evo, Milwaukee Eight 890567 Tappet adjustment tool JIMS Head Holder Adapters for 7mm Valve Guides The JIMS head holder tool makes pressing valve guides in and out simple. 622185 7mm Assembly Pilot 622186 7mm Insert GASKETS TRANNY & CLUTCH DRIVELINE WHEELS, TIRES & BRAKES FRAMES FORKS & SHOCKS Interconnect Seal Leak Testing Tool • Inspect properly your lower end assembly before sealing the cases • It checks the sealing of the interconnect seal OEM 45359-00 • For Twin Cam engines 00-17 890570 Interconnect seal leak testing tool JIMS Wrist Pin Reamers Use with rods in or out of motor. These tools will ream your wrist pin bushings to OEM specifications, and are made to exact tolerances with pilots to locate from the I.D. of your wrist pin bushings. They are easy to use with their lead-in taper at the start of each ream. 22320 Fits all single cam Big Twins from 36-99 (including all aftermarket engines) JIMS Cylinder Torque Plates Required to accurately bore late-model aluminum cylinders. Simulates stress deformation of installed cylinder. Drilled for multiple applications up to a 4"-bore. The plates for Twin Cam 88 models also fit Screamin‘ Eagle big bore cylinders. Optional bolts are available for use with Evolution Sportster and Buell cylinders. 20806 For Shovel and EVO 3.4375" to 4" 66-99 20291 For Twin Cam and 4.00" to 4.60" 99-17 20807 Optional bolt kit for use on 86-20 Sportster and 95-02 Buell used with CCE 20806 SHEETMETAL INSTRUMENTS & GAUGES LUBRICANTS & CHEMICALS TOOLS & EQUIPMENT for more details check www.custom-chrome-europe.com 19.35
