Views
2 years ago

6 ELECTRICAL

  • Text
  • Bus
  • Thundermax
  • Rotor
  • Stator
  • Regulators
  • Coils
  • Connectors
  • Battery
  • Module
  • System
  • Fuses
  • Relay
  • Module
  • Equalizer
  • Battery
  • Battery
  • Kabelbaum
  • Plugs
  • Batterie
Motorcycle wiring connectors, wiring harness, tuning modules, O2 sensors, CAN BUS modules, wiring modules, control units, load equalizers, relays, fuses, ignition systems, ignition modules, spark plugs, batteries, coils, regulators, stator, rotor

895517 6 895525 895524

895517 6 895525 895524 TLT Moto CAN Switchbox To convert handlebar controls, tacho or speedo on CAN Bus equipped models. This switchbox makes it possible! To ease up the connection to the bikes harness we offer a handlebar and a speedometer cable kit separately. For more detailed instructions visit our dealer store! 895523 TLT CAN switchbox 895524 TLT handlebar-cable-kit 895525 TLT speedometer-cable-kit 912574 912575 Z1 Standard Mid-Frame System by Wire Plus Same features as Z1 Mini but supplied with longer billet cover for mounting of both modules in one compact location. Mid-Frame system with harness for stock style handlebar controls. With lighting control module included. 640484 Sold each Wire Plus Flatside Tank Systems Mounts on the frame backbone of any bike equipped with flatside gas tanks as well as Softail models from 84-95. Water and vibration proof. Black anodized billet lid (CC #640349) is available to cover the module if it is installed in a visible area. 640348 Kit with chopper style harness for minimal system switches and provisions for turn signals Turn Signal Relay​ • All necessary components required for installation are included • Simple installation in feed to the indicator switch or swap the original 2-3 pole flasher relay • Connection to indicator control light also possible • Restricts the accompanying flashing of nonactivated indicators • Load-independent / steady flash rate • Switching capacity 0,5-50 watt • Very small dimensions 22 x12 x 6 [mm] (L/W/H) • Suitable for indicator switches • Suitable for 6 and 12 volt DC applications PART# FITMENT DESIGN UNIT 912574 R1 Each 912575 In certain cases the hazard warning flasher must be deactivated. R2 Each 6.18

ELECTRICAL APPAREL SEATS & TOURING FOOT CONTROLS HAND CONTROLS LIGHTING MD Cycle Control Box The cycle control box is one of the smallest units on the market. It allows the use of push buttons for functions such as hi-low beam, turn signals left and right, horn and last but not least it even has an option for a starter button! The unit can be used with conventional or LED turn signals. Due to its size it can be installed almost anywhere on the bike, even in the headlight! 50 mm x 45 mm x 21 mm (2” x 1 3/4” x 0.8”) 681572 MD Cycle Control Box 681897 MD Cycle Control Box including hazard light function 681898 MD Cycle Control Box including hazard light and self canceling turn signal function (17 seconds) Wire Plus 105-Series Wiring System The ultimate chopper-style wiring system! It features a solid-state breaker pack (breakers that will never burn out) that measures only 1" x 1" and is molded in waterproof epoxy with diagnostic LED’s. The pre-assembled harness is configured for an automotive start switch (switch sold separately) which eliminates start circuit wiring in the harness. This system is supplied with an installation kit that allows the builder to add indicator and turn signal wires. Custom applications. 640362 Complete kit Z1 Mini Mid-Frame System by Wire Plus These new systems have the smallest power modules ever! Designed for Bobber and Chopper style bikes with a round oil tank or springs under the seat with no place to hide anything. This module is supplied with a billet aluminum cover for visible mounting, with holes for viewing diagnostic lights. Measures just 1.8"-wide x 2"-tall x .85"-deep! Mounts anywhere in the oil tank area. Auto-cancel module sold separately (CC #24692). Mid Frame system with harness for stock style handlebar controls. With or without turns or auto-cancel. 640481 Sold each Blackbox 2 ELECTRICAL EXHAUST INTAKE ENGINE GASKETS 56 mm TRANNY & CLUTCH 37 mm DRIVELINE MD Cycle Control Databus System This little unit has the same functions as the standard MD Cycle Control box but instead of running five wires through and out of your handlebar there is only one wire that comes out and goes to the module which is hidden somewhere on the bike! There is no way to get a cleaner look. Detailed instructions included. 685430 Sold each Dual Latching Module by Wire Plus Designed to make your momentary push buttons on your hand controls latch like stock switches do. This module operates the Hi-low and Run-off latching circuits found on Original Equipment switches. 640486 Measures 1" x 1 1/4" x 1/2" Electronic Control Unit 2 for Push Button Handlebar Controls Especially designed for use with Ness handlebar controls with button switches. Controls horn, signal lights, low and high beam. This single box replaces all those small units that mess up the electricity of your bike and comes with instructions for installation. The new features of Unit 2 is a protection against short circuit, the smaller size, starter relais function and the pre set wiring. Made in Germany. 696285 Elektronic Box 2 WHEELS, TIRES & BRAKES FRAMES FORKS & SHOCKS SHEETMETAL INSTRUMENTS & GAUGES LUBRICANTS & CHEMICALS TOOLS & EQUIPMENT for more details check www.custom-chrome-europe.com 6.19

Can Bus Thundermax Rotor Stator Regulators Coils Wiring Connectors Lithium Battery Tuning Module Ignition System Harley Fuses Flasher Relay Control Module Load Equalizer Touring Battery Softail Battery Harley Kabelbaum Spark Plugs Harley Batterie