Views
4 years ago

19 TOOLS & EQUIPMENT

  • Text
  • Cruztools
  • Toolbox
  • Wrench
  • Tools
  • Wrench
  • Dongle
  • Diagnostic
  • Screws
  • Kits
  • Down
  • Tools
  • Tools
  • Tools
  • Hebebuehne
  • Lift
  • Ramps
  • Stand
  • Atal
  • Actia
  • Diagnostic
Tools, ramps, tie down straps, motorcycle locks, motorcycle lifts, shop dollies, battery chargers, tool kits (road side repairs), torque wrenches, specific engine tools, engine stands, bearing tools, diagnostic tools, screws

JIMS Wrist Pin/Rod

JIMS Wrist Pin/Rod Alignment Tool Checks rod straightness without removing rods from case. Measures 4 1/2"-long. 20298 Fits all single cam Big Twins ONLY (including aftermarket and S&S) Flywheel ‘Jam’ Tool Holds the crankshaft in the TDC (topdead-center) position when installing cams. It threads into the cases in place of the timing hole plug and permits you to snug it up to the flywheels with the timing mark showing through its hollow center. It was designed for use on Sportster engines which have a tendency to rotate past TDC when changing cams, but it may also be used on Big Twins. 20188 Sold each JIMS H-D Cruise Drive 6-Speed Maindrive Gear Remover Tool Removes the main drive gear from the main bearing correctly while in the transmission case. Eliminates the need of an arbor press and the risk of case damage 622054 Fits all 6-speed 06-17 Twin Cam and 17-23 M8 models Rod Alignment Tool • Use to check rod straightness without removing rods from case • The alignment tool is 4-1/2” long • Use on all Twin Cam A and B (Includes aftermarket motors) • .927” Wrist Pin 890573 Rod Alignment tool JIMS H-D Cruise Drive 6-Speed Maindrive Gear and Bearing Remover / Installer Kit Complete Kit for servicing the main drive gear or the main bearing on the latest H-D 6-speed transmission. Removes or installs both parts correctly without damaging the case. 622057 All Twin Cam H-D 6-Speed Cruise Drive models, 06-17 Dyna's and all 07-17 Twin Cam models JIMS Starter Jackshaft Seal Installer Tool This tool is designed to easily align and install the starter jackshaft seal (H-D No.12066) without distorting or damaging the seal. This seal is located in the upper part of the inner primary of Big Twins. Sold each. 622059 For all Twin Cam FL models 99-06, FXST models 00-06 & FXD models 99-05, and on all Big Twin EVO 94-00 Clutch Adjuster Nut Tool by Motion Pro • For use on all 98-17 Big Twin models excluding applications with hydraulic clutches • Deep socket allows tool to recess into clutch basket and can be driven with 11/16” combination wrench or adjustable wrench • Through hole allows access with hex wrench to hold clutch adjuster screw while simultaneously tightening the adjuster lock-nut • Heavy duty tool for shop or home use • Compact design fits easily in the saddle bag or tool roll 641128 Clutch Adjuster Nut Tool 19 19.40 Mainshaft Mainshaft Seal Remover The Milwaukee Eight has a new crankshaft oil seal that is difficult to remove without potentially damaging the crankcase bore. This new unique and exclusive JIMS tool is designed to do the job right, with no chance of damage to the case. Simply insert the removal fingers over the engine output shaft, and then slide the lock collar over the fingers. Once assembled, you can easily remove the seal square to the bore by simply turning a wrench. Part#: 917608 , Fitment: 17-23 Touring, 18-23 Softail, 17-23 Trike , Unit: Each , Qty.: 1 JIMS Inner Primary Cover Bearing and Seal Installer/ Remover Tool Designed to safely remove and install the inner primary bearing, (H-D No.9135) without any damage to the new bearing. This is done by pushing on the outer perimeter of the bearing. Also removes and installs inner primary seal, (H-D No.12052A). This is the bearing and seal that the transmission mainshaft passes through. Sold each. 622060 For all Late 84-05 Softail models, 85-06 Touring models and 85-05 FXR & Dyna models

APPAREL SEATS & TOURING JIMS Flywheel Runout (Trueness) Inspection Gauge Check flywheel runout of the pinion shaft while assembled in engine case. Also check the amount of gear lash on gear driven cams used in some twin cam engines. By using a JIMS tire rotator No. 936 you can remove most all of the stress being applied to the flywheel by not rotating the engine with the electric starter motor. Main Drive Gear Bearing and Seal Installation Tool Use this tool to safely install new main drive gear bearings and seal, with use of a small 1-ton press. This tool will hold bearings and seal square to its bore, eliminating any marring of the bearings and seals and installing both to the right depth. 622042 Fits all 6-speed 06-17 Twin Cam and 17-23 M8 models Transmission Main Drive Gear Tool Use to remove the large 2 1/4" hex nut from the end of main drive gear, which secures the rear drive trans pulley. Just thread the inner support collar to end of mainshaft, place the socket over the collar with a 1/2" drive tool, and unthread (right hand thread) the locknut. 622037 Fits all 6-speed 06-17 Twin Cam and 17-23 M8 models FOOT CONTROLS HAND CONTROLS LIGHTING ELECTRICAL 622183 Use on 70-17 Big Twin, Shovels, EVO and Twin Cam EXHAUST Gasket Locator Tool No. 968 by JIMS This tool will assist you in aligning the gaskets to avoid misalignment and oil leaks. Primary cover, cam cover, and transmission end cover gaskets are just a few of the possible applications. Install the locator tools into the gasket surfaces 1/4”- 20 threaded holes, slip on the gasket and the cover over the pins. Next, install a few cover mounting screws and snug down. Recover the tools and finish off with the remaining screws. 3 piece set. Transmission Door Removal Tool Use this tool to remove (pull) the complete door with gears and shafts from the transmission. Just prepare the trans for disassembly, bolt this tool to the outside of door, and place the two supplied press pins into the two screw holes of trans case. Thread in two of the screws, securing the door to cases, and the door is pulled from case. 622036 Fits all 6-speed 06-17 Twin Cam and 17-23 M8 models Primary Chain Locking Tool Use to lock the clutch hub sprocket to the front engine sprocket. With the two sprockets locked together, engine and clutch nuts can easily be removed and retorqued. 622035 Fits all 06-17 Dyna and 07-23 Softail models Primary Drive Lock Tool 894889 With step fits all models INTAKE ENGINE GASKETS TRANNY & CLUTCH DRIVELINE WHEELS, TIRES & BRAKES 640094 For use on all models with 1/4”- 20 threaded gasket surface mounting holes FRAMES JIMS 6-Speed Twin Cam Main Drive Gear Seal Installer This tool is designed to properly align and install, to the right depth, the main drive gear seal H-D No.12077 into the end of the gear. This can be performed while the assembled transmission is either on a bench or in the motorcycle chassis. Sold each. 622062 For all 6-speed 06-17 Twin Cam and 17-23 Milwaukee Eight Cruise Drive (Late 6 Speed Trans) Main Case Seal Installer H-D’s new 6-speed transmission is a very stout piece of engineering, incorporating some of the best bearings made. These main case bearings are of such high precision that you must be very gentle when working in or around them. For this reason, JIMS has developed a driver style seal installer (not a pushing or pulling type, which could damage these bearings). This new tool installs the main seal to the correct depth, without applying any stress to the new precision bearings, or new seals. 622190 Fits all 6-speed 06-17 Twin Cam and 17-23 M8 models for more details check www.custom-chrome-europe.com JIMS Primary Locking Bars To lock primary for service work. 20824 For 4-speed Big Twins and 5-speed Softail models 20825 For 5-speed FXR and FLT models 20826 For 91-20 Sportster and 95-10 Buell, except 08-10 1125 models FORKS & SHOCKS SHEETMETAL INSTRUMENTS & GAUGES LUBRICANTS & CHEMICALS TOOLS & EQUIPMENT 19.41

CCE Online Publication

Cruztools Teardrop Toolbox Torque Wrench Thread Cutting Tools Oxygen Sensor Wrench Tuning Dongle Serial Diagnostic Harley Screws Screw Kits Tie Down Twin Cam Tools Evolution Tools Harley Engine Tools Hebebuehne Motorcycle Lift Ramps Engine Stand Atal Actia Motorcycle Diagnostic