Views
4 years ago

19 TOOLS & EQUIPMENT

  • Text
  • Cruztools
  • Toolbox
  • Wrench
  • Tools
  • Wrench
  • Dongle
  • Diagnostic
  • Screws
  • Kits
  • Down
  • Tools
  • Tools
  • Tools
  • Hebebuehne
  • Lift
  • Ramps
  • Stand
  • Atal
  • Actia
  • Diagnostic
Tools, ramps, tie down straps, motorcycle locks, motorcycle lifts, shop dollies, battery chargers, tool kits (road side repairs), torque wrenches, specific engine tools, engine stands, bearing tools, diagnostic tools, screws

622180 622181 JIMS Top

622180 622181 JIMS Top Center Case Bolt Spot Facer Tool Added insurance when building a big bore Twin Cam engine. You have seen the center right case bolt thread that has become compromised from the larger cylinder spigot bore diameter? Now you can get back all the necessary case bolt retention by installing one of JIMS Through Bolts Kits. This tool is needed to spot face the right case so the bolt head will seat flat on the case surface. Use on all Twin Cam 99-17. 622180 Case Bolt Spot Facer Tool 622181 Center Through Bolt Kit JIMS Oxygen (O2) Sensor Wrench This tool is a must for removing and installing H-D’s new 4 wire heated Oxygen Sensors. The new fragile O2 sensor must be torqued to 14 ft-lbs, lending to the design of this tool to be used with a 3/8” drive torque wrench. 622187 Use on 12-17 Dyna, 12-17 Softail, 10-16 Touring 622187 Valve Guide Driver Set 3 piece driver set for valve guide installation and removal on Big Twin and Sportster models. Includes drivers for 5/16", 11/32", and 3/8" I.D. guides. 400562 JIMS Exhaust Gasket (Seal) Installer Tool No longer do you need to fight trying to install this fragile exhaust seal. You’ll never worry about an exhaust leak again. Tool can be used with exhaust flange nuts, or JIMS handle CCI No. 20666 sold separately. Either way will position the seal evenly into the exhaust port of head. 622182 Use on all 84-23 EVO Big Twins, XL, and all Twin Cam models, Milwaukee Eight JIMS Exhaust Stud Drill Plate Guides and aligns the drill bit when removing broken exhaust studs. Use with a tap after to clean the threads. Can be used in the frame. Includes drill bit. 20940 For Evolution and Twin Cam models JIMS Pushrod Cover Clip Installing and Remover Tool Made from black delrin, this tool will NOT marr or slip – and will install the clip professionally with just one hand in seconds! It’s a luxury tool that you will appreciate for years to come. 622184 Use on all V-Twins that use pushrod clips.Ç JIMS Valve Spring Compressor Designed specifically for the heads on Evolution models, but will work with all Big Twins. It features a hardened ball bearing at the valve head end to eliminate damage to valves. Comes with new valve collar receiver for safer tool usage. 20696 For all Evolution Big Twin and Sportster engines Valve Spring Compressor Tool Use this collar with CC #20696 to remove and replace valves and conical (beehive) springs. A must-have tool for safe valve work. 622039 Fits all 04-20 Sportster, 05-17 Twin Cam and 04-10 Buell models, except CVO models 19 19.36 Oxygen Sensor Socket Tool This tool is used to remove or install the oxygen sensor on all closed loop fuel injected H.D. models. Socket has a 3/8" drive receiver or can be used with a 7/8" wrench. Socket will withstand up to 125 ft/lbs of torque. 640091 For use on all EFI models 06-11 (except 10- touring) JIMS Head Bolt Torque Gauge for Evolution Engines Allows the measuring of 90° when tightening head bolts. Torque sequence laser-etched on gauge. 20805 For all Twin Cam, Evolution and Sportster engines from 84-17

20716 APPAREL SEATS & TOURING 20676 FOOT CONTROLS JIMS Valve Guide and Seal Tools Precision tools permit accurate installation of shoulderless valve guides and seals. 20676 For installation of shoulderless valve guides to the proper depth on all Big Twin models 84-04 with .560” Dia. guides, including aftermarket heads. Use with installer tool 20716 below. Sold each 622048 For all Big Twins 05-17 with 7mm valve guides, Sportster 04-20, Buell 04-10 (except 1125 models, Touring 17). Use with handle 622047 below. Sold each Shoulderless Valve Guide Removal Tool and Installation Tool Handle Used to remove shoulderless valve guides and with above tools for installation. 20716 For all Big Twins to 04. Sold each 622047 For all Big Twins 05-17 with 7mm valve guides, Sportster 04-20, Buell 04 -10 (except 1125 models, Touring 17). Use with 622048 above. Sold each JIMS Pinion Gear Puller Used to remove the pinion gear on all Big Twin and Sportster models (except Twin Cam models). May also be used to install pinion gear on Big Twin 39-89 and Sportster models from 57-76. Collar included. 20698 Replaces OEM 96830-51 JIMS Pinion Bushing Puller Removes pinion bushing from cam cover in one easy operation. 20445 For Big Twins from 54-99 (exc. 99 Twin Cam) JIMS Rocker Bushing Reamer Precision reamers made from the finest heat-treated tool steel, and accurately dimensioned to exacting tolerances. Used for precision alignment and sizing of rocker bushings. 20692 For 66-17 Big Twin, except 17 M8, 57-20 Sportster, 95-10 Buel, except 08-10 1125 JIMS Tappet Block Alignment Tool Used to make sure the roller tappet tracks on the center line of the cam lobe. 20670 Fits Big Twins from late 77-99 (exc. 99 Twin Cam) 20670 HAND CONTROLS LIGHTING ELECTRICAL EXHAUST INTAKE ENGINE GASKETS TRANNY & CLUTCH DRIVELINE JIMS Gear Shaft Nut Socket Wrench Secures the pinion gear nut to the pinion gear shaft. Fits Big Twins from 55-92. 20690 Replaces OEM 94555-55A WHEELS, TIRES & BRAKES FRAMES JIMS Rocker Bushing Puller Removes rocker arm bushings or roller bearings in one easy operation. FORKS & SHOCKS 20446 For Big Twins from 66-17 (except Touring 17) and Sportster or Buell models from 57-20(exc. Buell 1125) SHEETMETAL JIMS Pinion Gear Lock Tool Locks pinion gear, necessary to torque the pinion nut. Tool screws to case and holds pinion gear stationary. 20785 For Big Twin models from 54-99 (except Twin Cam 88 models) S&S Compression Release Socket Kit Special two-piece compression release socket kit permits in-frame installation of S&S compression releases while protecting wiring from damage during installation. 601711 Two-piece socket kit INSTRUMENTS & GAUGES LUBRICANTS & CHEMICALS TOOLS & EQUIPMENT for more details check www.custom-chrome-europe.com 19.37

CCE Online Publication

Cruztools Teardrop Toolbox Torque Wrench Thread Cutting Tools Oxygen Sensor Wrench Tuning Dongle Serial Diagnostic Harley Screws Screw Kits Tie Down Twin Cam Tools Evolution Tools Harley Engine Tools Hebebuehne Motorcycle Lift Ramps Engine Stand Atal Actia Motorcycle Diagnostic