Views
4 years ago

19 TOOLS & EQUIPMENT

  • Text
  • Cruztools
  • Toolbox
  • Wrench
  • Tools
  • Wrench
  • Dongle
  • Diagnostic
  • Screws
  • Kits
  • Down
  • Tools
  • Tools
  • Tools
  • Hebebuehne
  • Lift
  • Ramps
  • Stand
  • Atal
  • Actia
  • Diagnostic
Tools, ramps, tie down straps, motorcycle locks, motorcycle lifts, shop dollies, battery chargers, tool kits (road side repairs), torque wrenches, specific engine tools, engine stands, bearing tools, diagnostic tools, screws

Transmission Case

Transmission Case Shifter Seal Installer These two simple tools make installing the shifter shaft seal precise and effortless. They align, center and install the shifter seal to the right depth on all EVO and Twin Cam Big Twin & Sportster models. 619299 Use to install H-D seal No.37101- 84B, 11000101 on 06-23 6-speed transmission and 84-05 Sportster 619300 Use to install H-D seal No. 12045 on all EVO Big Twins 80-99 or on H-D Twin Cam 5-Speed 99-06 FXST, FLH and FXD -05. Jims Ignition Alignment Tool The professional technician needs fast and accurate alignment of the ignition switch cover. Fiddling with screwdrivers and coat hangers does not cut it! Our alignment tool is the perfect solution; correct alignment is quickly and easily achieved. This tool is for 2014 and later touring models and based on our proven design for earlier models. 642290 Alignment tool for 14-23 HDI Touring models JIMS Outer Balancer Bearing Installer & Remover Tool This tool removes and installs the outboard balancer bearing on the new 96” and 110” “B” Softail engine’s chain guide support plate. Sold each. 622056 For all Softail models 07-17 19 19.30 FXST Rear Seat Mounting Screw Tool The JIMS tool locates on the seat screw head to keep from scratching or damaging the rear fender, or screw, when installing or removing the seat. 619301 Use on 07-23 Softail models using the H-D screw No. 3075 Jims Angled Feeler Gauge This new innovative feeler gauge holder eliminates the need to use bulky multi feeler gauge tools while performing valve adjustments. This tool is ideal for reaching down into small tight areas and incorporates an angle to help reach around corners, often necessary for adjusting valves. Tool includes two handles with: .002”, .003”, .004”, .005”, .006” and .008” inserts. 619304 Feeler Gauge Kit JIMS Ignition Switch Housing Alignment Tool This tool will easily align the ignition switch housing as the retaining screws are being torqued. This gives the ignition switch knob the alignment it needs to help extend the life of the ignition switch housing. Sold each. 622051 For all FL models 03-13, V-Rod models 02-17 622051 JIMS Balancer Shaft Removal Tool This tool is designed to remove both front and rear counter-balancer shaft bearing assembly from the left engine case on the new 96” and 110” Beta engines. Sold each. 622058 For all Softail models 07-17 JIMS Twin Cam Timken Case Bearing Conversion Tool This tool is a must for the big cubic inch late model Twin Cam engine builder. It may also be used to replace bearing for stock 88" or 96" engines. Utilizing the special JIMS precision insert, it is designed to easily and accurately convert the left side crankshaft roller bearing (H.D. No.24604-00D) to the more durable Timken Bearing (H.D. No.9028). This insert is manufactured from aluminum that is several times stronger than the aluminum case material the standard bearing rides in. The Tool Includes: • A new steel bearing insert held to under .0002” TIR (total indicator reading). • A press plate that will hold the bearing insert in line with the case bearing bore at the time it is being pressed into case. • All the necessary drill bits to drill oil feed and return holes, hardware, and detailed instructions. This job can be performed with normal hand tools, a hand drill, and a 2 ton press. *Order Bearing Inserts & Timken Bearings separately. 640097 Tool for use on Twin Cam engines 03-17 640098 Stainless steel Timken case bearing insert kit

APPAREL SEATS & TOURING FOOT CONTROLS JIMS BETA Balancer Inner Bearing Remover/ Installer Accurately and safely install or remove the inner balancer bearing mounted in the left engine case. Designed for early or late Beta cases 00-17. 622043 Beta cases 00-17 JIMS Balancer Shaft Retention Pins Use this tool to secure the engine balancers on Twin Cam 88 “B” engines when servicing the flywheel assembly. This tool locks into the balancer’s sprocket pin holes to prevent the balancer from turning out of sync with the flywheel. 671017 For Twin Cam 88 Softail models from 00-17 HAND CONTROLS LIGHTING ELECTRICAL EXHAUST INTAKE JIMS Balancer Shaft Alignment Tool This tool is a must-have for maintaining a long life of your balancer’s drive chains and bearings. It takes the guess work out of setting up your sprocket and chain alignment on both early and late Twin Cam Softail engine and checks chain alignment between balancers and crankshaft. 671014 For all Twin Cam 88 and 96" Softail models from 00-17 FL Power Train Alignment Tool by JIMS This tool easily and safely aligns the Power Train, (rubber mounted engine, transmission and the swingarm assembly) to the correct position as found on most touring models. Alignment service must be performed when the engine, transmission, or swingarm has either been removed or repaired. The safety in handling and performance of the motorcycle could be greatly effected without the accurate alignment this tool provides. 640096 For use on 93-08 FLHT models ENGINE GASKETS TRANNY & CLUTCH DRIVELINE WHEELS, TIRES & BRAKES 622063 622064 FRAMES JIMS Fuel Pump Retainer Remover Tool This is a must use tool for removal or installation of the retaining ring otherwise you run the risk of developing a fuel leak. This tool safely removes the retaining ring holding the fuel pump. Use for quick and easy service of fuel filter and other fuel related parts. Sold each. 622055 For all 08-23 Touring and 09-23 Trike models for more details check www.custom-chrome-europe.com JIMS Twin Cam Engine Rotator Socket Use this tool to rotate the flywheel/piston assembly, with the engine still in frame or on a bench. This tool is used to rotate the flywheel assembly when doing pushrod adjustments, when building big inch engines, checking operating clearances such as piston to piston, or valve to valve. Can also be used to hold the flywheel assembly from rotating when torquing the cam drive sprockets retention bolts. This tool has been manufactured with a long socket design making it easier to use without the use of a 1/2” drive extension on your 1/2” driver. For engine bench work we recommend the engine be bolted in a JIMS engine stand. Sold each. Caution: Not for use with air or electric impact, this tool is only guaranteed for use with hand drivers, “not impacts”. 622063 For all 06-17 FXD & 07-17 FXST, & FL models 622064 For all Big Twins 55-06 models (except 06 FXD) FORKS & SHOCKS SHEETMETAL INSTRUMENTS & GAUGES LUBRICANTS & CHEMICALS TOOLS & EQUIPMENT 19.31

CCE Online Publication

Cruztools Teardrop Toolbox Torque Wrench Thread Cutting Tools Oxygen Sensor Wrench Tuning Dongle Serial Diagnostic Harley Screws Screw Kits Tie Down Twin Cam Tools Evolution Tools Harley Engine Tools Hebebuehne Motorcycle Lift Ramps Engine Stand Atal Actia Motorcycle Diagnostic