Views
3 months ago

19 TOOLS & EQUIPMENT

  • Text
  • Cruztools
  • Toolbox
  • Wrench
  • Tools
  • Wrench
  • Dongle
  • Diagnostic
  • Screws
  • Kits
  • Down
  • Tools
  • Tools
  • Tools
  • Hebebuehne
  • Lift
  • Ramps
  • Stand
  • Atal
  • Actia
  • Diagnostic
Tools, ramps, tie down straps, motorcycle locks, motorcycle lifts, shop dollies, battery chargers, tool kits (road side repairs), torque wrenches, specific engine tools, engine stands, bearing tools, diagnostic tools, screws

20629 20695 JIMS Cam

20629 20695 JIMS Cam Bearing Puller Once the cams are removed from the support plate, this tool will remove the bearing. Unlike a general purpose puller this tool was designed to remove the bearing straight with no slipping or binding. 20296 For Twin Cam 88 models from 99-06 (except 06 Dyna) JIMS Cam Tools Bearing Puller Easily pulls the inner cam bearing without splitting the cases. It also keeps the rollers from coming out during removal. 20695 Fits Big Twin models from 58-99 (except Twin Cam 88 models) Cam Bushing Reamer Line reams cam cover bushings from inner cam bearing for a true centerline between the two dimensions. 20629 Fits Big Twin models from 70-99 (except Twin Cam 88 models) JIMS Inner Cam Bearing Installation Tool for Big Twins Smoothly presses the inner cam bearing to the right depth into the right-side case when both case halves are assembled. 20774 For all Big Twin models from 58-99 JIMS Cam Seal Installer/Remover for Late Model Big Twins Install or remove cam seal without removing the cam cover. Easy-to-use tool pulls the seal and drives in a new one flat and square for a no-leak repair. The tool can also be used to remove the cam cover from the case. 20762 For all Big Twins from 86-99 (except Twin Cam) JIMS Cam Gear Remover and Installer This precision tool will remove the cam gear on any single cam Big Twin from 70-99, and reposition it on another cam shaft in exactly the same spot. Pressing the gear on in the advanced or retarded position is also possible. Save time and ensure accuracy time after time. 400340 Complete kit Motion Pro Degree Wheel Aluminum construction with a 6 3⁄4" outside diameter and a 6 mm center hole. Can be used on all motorcycles to check or set up ignition timing. May also be used on 4-stroke engines to check or alter cam timing. Sold each. 5008092 Motion Pro Degree Wheel 19 19.26 JIMS Inner Cam Bearing Remover Designed like the version for Evolution models, it removes the bearing easily without any damage to the crankcase. This precision-built tool will also keep the pin rollers from accidentally falling into the crankcase. 20292 For Twin Cam 88 models from 99-06 JIMS Bearing Race Drivers Cam Bearing Driver Used to install inner cam bearing. Fits single cam Big Twins from 58-99. Sold each. 20699 Replaces OEM 97272-60 Driver Handle Handle for bearing drive tools. Sold each. 20666 Driver Handle JIMS Piston Support Plate Using this tool will give you peace of mind when installing your rings and cylinders by providing a non-marring flat support to push the bottom of the piston agents as you install the rings and cylinder over the piston. 671018 Use on all Harley-Davidson engines

TOOLS & EQUIPMENT APPAREL SEATS & TOURING 607717 JIMS Cam & Pinion Gear Gauge Pins Use to check gear diameters when changing cams or pinion gears on single cam Big Twins ONLY. Sold in pairs. 400362 Fits Big Twins from 54-89 (.105" pins) 400363 Fits Evolution Big Twins from 90-99 (.108" pins) JIMS Wrist Pin Bushing Tool Makes it easy to remove and install rod bushings on all models (except Twin Cam 88 models). Complete instructions guide you through removal, selection of new bushing with the proper clearances, and installation. 20169 Fits all Big Twin Single Cam models up to 99. Fits Sportster, Buells and 45-19 (exc. 99 Twin Cam). FOOT CONTROLS HAND CONTROLS LIGHTING ELECTRICAL 607718 Timing Lights Suitable for 4- and 2-stroke engines with ignition adjustment angle 0-60°. Connection to vehicle battery 12 V. 607717 SKB 82 Suitable for 4- and 2-stroke engines with ignition adjustment angle 0-90° Revolution counting 500 – 9990 rpm. Connection to vehicle battery 12 V. 607718 SKB 84 Top Dead Center Piston Stop Tools These handy tools from S&S are used to set the piston at TDC. Fit all Big Twin and Sportster models from 36-17 except Touring 17. Sold each. 24522 Fits all Big Twin and Sportster models with 14mm sparkplug holes from 36-99 24523 12mm for Twin Cam 88 models, Evolution Sportster models, and RevTech heads EXHAUST INTAKE ENGINE GASKETS Connecting Rod Clamping Tool Holds rod when fitting piston pin bushing. Used on all V-twin models (repl. OEM 95952- 33). Sold each. 400548 Connecting Rod Clamping Tool JIMS Piston Ring Compressor Extra fine tooth ratcheting mechanism will compress rings in small increments without breaking. Includes six bands ranging from 2 7/8" to 4 3/8". 400357 JIMS Wrist Pin Remover Tool This simple tool can be used easily by one person. No need to get another technician to hold the piston while your drift the pin out. (99-06 Twin Cam) 20287 99-06 Twin Cam (except 06 Dyna) TRANNY & CLUTCH DRIVELINE WHEELS, TIRES & BRAKES FRAMES FORKS & SHOCKS Cam Gear Gauge Pins These pins are used to properly determine cam and pinion gear sizes. Sold in pairs. 24196 0.105"-diameter BT 54-89 24197 0.108"-diameter BT 90-99 (except Twin Cam) and aftermarket JIMS Wrist Pin Bushing Tool Removes and replaces the wrist pin bushing without removing the connecting rod from the crankcases. 20295 For Twin Cam 88 models from 99-06 JIMS Piston Pin Keeper Tool Makes piston pin retaining ring installation a snap. Fits stock piston pin retainers on Big Twins from 83-99 (except Twin Cam 88 models) and Sportster models from 85-19, 87-10 Buell (exc. 1125). 20674 Sold each SHEETMETAL INSTRUMENTS & GAUGES LUBRICANTS & CHEMICALS TOOLS & EQUIPMENT for more details check www.custom-chrome-europe.com 19.27

CCE Online Publication

1 APPAREL
2 SEATS & TOURING
3 FOOT CONTROLS
4 HAND CONTROLS
5 LIGHTING
6 ELECTRICAL
7 EXHAUST
9 ENGINE
10 GASKETS
11 TRANNY & CLUTCH
12 DRIVELINE
13 WHEELS, TIRES & BRAKES
14 FRAMES
15 FORKS & SHOCKS
16 SHEETMETAL
17 INSTRUMENTS & GAUGES
19 TOOLS & EQUIPMENT
01-2019 Rhine Time
02-2019 10 Years Anniversary BOAR Bikes
01-2018 BOAR Bike Fusion
03-2018 BOAR Bike CCEagle
05-2018 BOAR Bike CrossBob
04-2018 BOAR Bike H9 Sportster
2014 BOAR Video Sexy Thing
2015 BOAR Video THIS_IS
2017 BOAR Video AT NIGHT
2016 BOAR Ride Video Ride Unrivalled
02-2018 MBE Verona Bikeshow
03-2018 European Bike Week Faak
2016 CC-Riders
CCE SPECIAL FEATURE Cafe+Dirt Track
Cruztools Teardrop Toolbox Torque Wrench Thread Cutting Tools Oxygen Sensor Wrench Tuning Dongle Serial Diagnostic Harley Screws Screw Kits Tie Down Twin Cam Tools Evolution Tools Harley Engine Tools Hebebuehne Motorcycle Lift Ramps Engine Stand Atal Actia Motorcycle Diagnostic