Views
5 months ago

19 TOOLS & EQUIPMENT

  • Text
  • Cruztools
  • Toolbox
  • Wrench
  • Tools
  • Wrench
  • Dongle
  • Diagnostic
  • Screws
  • Kits
  • Down
  • Tools
  • Tools
  • Tools
  • Hebebuehne
  • Lift
  • Ramps
  • Stand
  • Atal
  • Actia
  • Diagnostic
Tools, ramps, tie down straps, motorcycle locks, motorcycle lifts, shop dollies, battery chargers, tool kits (road side repairs), torque wrenches, specific engine tools, engine stands, bearing tools, diagnostic tools, screws

Twin Scan II by Daytona

Twin Scan II by Daytona Twin Tec The new Twin Scan II provides diagnostic capabilities not found in other tools. It’s especially useful for diagnosing hard to find intermittent trouble codes. The motorcycle can be operated while the unit is installed. Under normal conditions (no trouble code), the unit will store data for the last hour of operation. If a trouble code is set, the unit automatically stops logging data 30 minutes after the code is set. This allows you to examine data before and after the code was set, even days later. • Requires laptop PC for display, and includes Windows software • Reads and clears diagnostic trouble codes from ECU (engine control unit), TSSM (turn signal/ security module), speedometer, and tachometer • Real time display of engine data on instrument panel type display • Built-in data logging • Stores up to one hour of data • Automatically triggers when a trouble code is set • Shows data before and after code is set • Includes two analog inputs for air/fuel ratio (AFR) Compatible with 01-17 fuell injected models using Delphi system (including V-Rod) with 1850 databus and 03-06 carbureted models with new 12 pin ignition module. Not compatible with 11up Stoftail models, 14-up Sportster, 14-up Touring and 12up Dynas with CAN data bus. 672529 Sold each JIMS Audio Isolation Tool The JIMS SoundStik is designed to listen to unique range of non-audible ultra sounds which are extremely useful in engine diagnostics & noise isolation. 619293 Audio isolation tool JIMS Engine Dipstick Socket Tool 619298 Tool, engine dipstick socket Dyna Ignition Switch Fork Lock Tool This tool is used to make removing and installing the Dyna ignition switch & fork lock simple. This tool locates on the ignition switch face nut that holds the switch in place on the frame, letting you remove or install this switch correctly. 619302 Dyna 06-17 JIMS Mega Nut For Cruise Drive By installing this mega nut correctly you can feel confident that your rear pulley will never come loose from your main drive gear. New for 2011, this nut is now available for late model Cruise Drive Transmission. 619297 For all H-D 6-speed Cruise Drive Transmissions 06-17, FXD’s and 07-19 FLH’s and FXST’s. 19 19.22

TOOLS & EQUIPMENT APPAREL SEATS & TOURING FOOT CONTROLS Transmissoin Case Shifter Seal Installer These two simple tools make installing the shifter shaft seal precise and effortless. They align, center and install the shifter seal to the right depth on all EVO and Twin Cam Big Twin & Sportster models. 619299 Use to install H-D seal No. 37101-84B on 06-19 H-D 6-Speed Cruise Drive transmissions and 84-05 Sportsters 619300 Use to install H-D seal No. 12045 on all EVO Big Twins 80-99 or on H-D Twin Cam 5-Speed 99-06 FXST, FLH and FXD -05. Jims Ignition Alignment Tool The professional technician needs fast and accurate alignment of the ignition switch cover. Fiddling with screwdrivers and coat hangers does not cut it! Our alignment tool is the perfect solution; correct alignment is quickly and easily achieved. This tool is for 2014 and later touring models and based on our proven design for earlier models. 642290 Alignment tool for 14-19 Touring Models JIMS Outer Balancer Bearing Installer & Remover Tool This tool removes and installs the outboard balancer bearing on the new 96” and 110” “B” Softail engine’s chain guide support plate. Sold each. 622056 For all Softail models 07-17 HAND CONTROLS LIGHTING ELECTRICAL EXHAUST INTAKE ENGINE FXST Rear Seat Mounting Screw Tool The JIMS tool locates on the seat screw head to keep from scratching or damaging the rear fender, or screw, when installing or removing the seat. 619301 Use on 07-19 Softail models using the H-D screw No. 3075 Jims Angled Feeler Gauge This new innovative feeler gauge holder eliminates the need to use bulky multi feeler gauge tools while performing valve adjustments. This tool is ideal for reaching down into small tight areas and incorporates an angle to help reach around corners, often necessary for adjusting valves. Tool includes two handles with: .002”, .003”, .004”, .005”, .006” and .008” inserts. 619304 Feeler Gauge Kit JIMS Ignition Switch Housing Alignment Tool This tool will easily align the ignition switch housing as the retaining screws are being torqued. This gives the ignition switch knob the alignment it needs to help extend the life of the ignition switch housing. Sold each. 622051 For all FL models 03-13, V-Rod models 02-17 622058 JIMS Balancer Shaft Removal Tool This tool is designed to remove both front and rear counter-balancer shaft bearing assembly from the left engine case on the new 96” and 110” Beta engines. Sold each. 622058 For all Softail models 07-17 JIMS Twin Cam Timken Case Bearing Conversion Tool This tool is a must for the big cubic inch late model Twin Cam engine builder. It may also be used to replace bearing for stock 88" or 96" engines. Utilizing the special JIMS precision insert, it is designed to easily and accurately convert the left side crankshaft roller bearing (H.D. No.24604-00D) to the more durable Timken Bearing (H.D. No.9028). This insert is manufactured from aluminum that is several times stronger than the aluminum case material the standard bearing rides in. The Tool Includes: • A new steel bearing insert held to under .0002” TIR (total indicator reading). • A press plate that will hold the bearing insert in line with the case bearing bore at the time it is being pressed into case. • All the necessary drill bits to drill oil feed and return holes, hardware, and detailed instructions. This job can be performed with normal hand tools, a hand drill, and a 2 ton press. *Order Bearing Inserts & Timken Bearings separately. 640097 Tool for use on Twin Cam engines 03-17 640098 Stainless steel Timken case bearing insert kit GASKETS TRANNY & CLUTCH DRIVELINE WHEELS, TIRES & BRAKES FRAMES FORKS & SHOCKS SHEETMETAL INSTRUMENTS & GAUGES LUBRICANTS & CHEMICALS TOOLS & EQUIPMENT for more details check www.custom-chrome-europe.com 19.23

CCE Online Publication

1 APPAREL
2 SEATS & TOURING
3 FOOT CONTROLS
4 HAND CONTROLS
5 LIGHTING
6 ELECTRICAL
7 EXHAUST
9 ENGINE
10 GASKETS
11 TRANNY & CLUTCH
12 DRIVELINE
13 WHEELS, TIRES & BRAKES
14 FRAMES
15 FORKS & SHOCKS
16 SHEETMETAL
17 INSTRUMENTS & GAUGES
19 TOOLS & EQUIPMENT
01-2019 Rhine Time
02-2019 10 Years Anniversary BOAR Bikes
01-2018 BOAR Bike Fusion
03-2018 BOAR Bike CCEagle
05-2018 BOAR Bike CrossBob
04-2018 BOAR Bike H9 Sportster
2014 BOAR Video Sexy Thing
2015 BOAR Video THIS_IS
2017 BOAR Video AT NIGHT
2016 BOAR Ride Video Ride Unrivalled
02-2018 MBE Verona Bikeshow
03-2018 European Bike Week Faak
2016 CC-Riders
CCE SPECIAL FEATURE Cafe+Dirt Track
Cruztools Teardrop Toolbox Torque Wrench Thread Cutting Tools Oxygen Sensor Wrench Tuning Dongle Serial Diagnostic Harley Screws Screw Kits Tie Down Twin Cam Tools Evolution Tools Harley Engine Tools Hebebuehne Motorcycle Lift Ramps Engine Stand Atal Actia Motorcycle Diagnostic